Welcome To b2b168.com, Join Free | Sign In
中文(简体) |
中文(繁體) |
Francés |Español |Deutsch |Pусский |
| No.10144069
![](http://i.b2b168.com/e/tag_pthy.gif)
- Product Categories
- Friendly Links
- home > Supply > Gaomi punch manufacturers, manufacturers of high-density punch, punch density Huali well-known manufacturers in Shandong
Gaomi punch manufacturers, manufacturers of high-density punch, punch density Huali well-known manufacturers in Shandong
Information Name: | Gaomi punch manufacturers, manufacturers of high-density punch, punch density Huali well-known manufacturers in Shandong |
Published: | 2013-11-27 |
Validity: | 0 |
Specifications: | Limitation |
Quantity: | |
Price Description: | |
Detailed Product Description: | Gaomi Huali Forging Machine Co. (http://www.gmhljc.com) is located in Weifang City, Shandong Weifang People Street West first Gaomi City, Shandong Province, 200 meters west of the airport depot, Contact: Mr. Sun to work after 1 mechanical, hydraulic, pneumatic and other operating handle, cutting the door, switch plates and other non-operating position; 2, stop the machine running, turn off the power, gas supply; 3, remove iron, cleaning the job site, carefully wipe the machine. Rail surface, turning and sliding surface, positioning surface, countertops, etc. refueling and maintenance; 4, seriously question the classes found in the machine, fill the shift record book, do shift work. Electrical fault diagnosis method CNC machine fault diagnosis fault detection, fault isolation and fault location judgments and three stages. Fault detection of the first phase of the CNC machine is to be tested to determine whether there is a fault; nature of the second stage is to determine the fault and isolating the failed component or module; third stage is to locate the fault or the printing module can be replaced board to shorten the repair time. In order to detect system failures occur Gaomi press manufacturers to quickly identify parts of the fault and can be immediately removed, requiring troubleshooting should be as small and simple, the time required for fault diagnosis should be as short as possible. To do this, you can use the following diagnostic methods: [1] method uses an intuitive sense organs, failure of attention when various phenomena, such as the presence or absence of spark, light punch manufacturers to produce high-density, with or without abnormal noise fault, where abnormal fever and the presence of coke burnt taste like. Carefully observe the surface condition of each printed circuit board may be faulty, with or without signs of burning and damage to further narrow the scope of the inspection, which is a basic, the most commonly used method. Self-diagnostic data and status checks CNC system failure alarm information can be displayed not only on CRT monitors, but also provide the machine parameters and status information in the form of the "Diagnostic address" multi-page and "Diagnostic data", common data and status checks There are two kinds of parameter checking and interface checks. (1) Check the parameters of CNC machine tools is an important parameter data through a series of tests and adjustments obtained, is to ensure the normal operation of the machine. These data include the gain, acceleration, contour monitoring tolerance, backlash compensation and leadscrew compensation value and so on. When subjected to external interference punch manufacturers, cause data loss or chaos, the machine does not work. (2) Enter the examination system and the CNC machine interface between the I / O interfaces, including the interface between the input signal CNC systems and PLC, PLC and Machine / output signals. Enter the NC system / output interface can diagnose the state of all switch signal is displayed on the CRT display manufacturers punch density of Weifang, with "1" or "0" indicates whether the use of state of the signal display can check whether the system has CNC signal to the machine side, switch the machine side, such as whether the input signal to the CNC system, which can locate the fault on the machine side or in CNC systems. |
Admin>>>
You are the 26658 visitor
Copyright © GuangDong ICP No. 10089450, Gaomi China Forging Machine Co. All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility
You are the 26658 visitor
Copyright © GuangDong ICP No. 10089450, Gaomi China Forging Machine Co. All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility